Tiles & Stone Installation Solutions

  • ADDCON TILE ADHESIVE – SILVER

    Interior Wall & Floor Tile Adhesive

    Description

    ADDCON Tile Adhesive is a ready to use tile adhesive based on grey cement and special chemicals providing non shrink, self curing, waterproof excellent adhesive for Vitrified Tile and ceramic tiles. Suitable for both horizontal and vertical surfaces.

    Advantage

    IMG_0467

    • Ready to use, only water to be added.
    • Waterproof
    • Excellent bond than conventional cement based mortar
    • Self curing
    • Good mechanical strength
    • Applicable both horizontal and vertical surfaces
    • Increase flexibility
    • Impact Resistance

    Instruction for use

    Surface should be sound and mechanically cleaned to remove all loosely adhering particals,oil, grease etc. Pre-wetting of substrate is essential with maximum saturation of water but surface dry (S.S.D.) condition. Tiles shall be cleaned of dust with brush/cloth but shall be dry while using. ADDCON Tile Adhesive should be poured in the ratio of SC : W = 1: 0.25 to 0.30 by wt.into potable water slowly while stirring continuously to get smooth paste. Allow 5 minutes interval and stir again. Apply the paste on prepared surface with 5mm approx.thickness. and comb the surface with notched trowel.Place tiles within 2 hours of mixing and press firmly with twisting movement.Uneven surface may require more than 5mm thickness. Use damp cloth to remove excess paste from tile surface. Tile joints may be filled by ADDCON Tile grout.

    Coverage

    4kg to 5 kg per sq.mtr./5 mm. Thickness for flat surface (indicative)

    Packing

    20/25/50 kg Bag

    Storage

    Keep in a dry place, avoid moisture ingress.

    Caution

    Add powder to water. Prepare only required quantity to utilize within 2 hours. Avoid fixing tiles outdoor when rain is imminent. Correct ratio of ADDCON Tile Adhesive and water is essential for optimum performance.

    Important Technical Data

    • Aspect : Grey Powder
    • Bulk Density : Around 1.35 (kg/ lit).
    • Bad Thickness s: 3-6 mm
    • Open time : 20-30 Minutes
    • Pot Life : 1.5 Hrs
    Need Customer Input

  • ADDCON TILE ADHESIVE – HIGH

    Grey Interior & Exterior Wall, Floor Tiles & Stone Adhesive

    Description

    ADDCON TILE ADHESIVE-HIGH is a ready to use tile adhesive based on grey cement and special chemicals providing non shrink, self curing, waterproof excellent adhesive for vertified Tile and ceramic tiles. Suitable for both horizontal and vertical surfaces, interior and exterior applications.

    Advantage

    • Ready to use, only water to be added.                                                                 982a2137
    • Water resistance
    • High Strength
    • Good mechanical strength
    • Applicable both horizontal and vertical surfaces
    • Increase flexibility
    • Impact Resistance

    Instruction for use

    Surface should be sound and mechanically cleaned to remove all loosely adhering particals,oil, grease etc. Pre-wetting of substrate is essential with maximum saturation of water but surface dry (S.S.D.) condition. Tiles shall be cleaned of dust with brush/cloth but shall be dry while using. ADDCON Tile Adhesive should be poured in the ratio of SC : W = 1: 0.25 to 0.30 by wt.into potable water slowly while stirring continuously to get smooth paste. Allow 5 minutes interval and stir again. Apply the paste on prepared surface with 5mm approx.thickness. and comb the surface with notched trowel.Place tiles within 2 hours of mixing and press firmly with twisting movement.Uneven surface may require more than 5 mm thickness. Use damp cloth to remove excess paste from tile surface. Tile joints may be filled by ADDCON Tile grout.

    Coverage

    4kg to 5 kg per sq.mtr./5 mm. Thickness for flat surface (indicative)

    Packing

    20/25/50 kg Bag

    Storage

    Keep in a dry place, avoid moisture ingress.

    Caution

    Add powder to water. Prepare only required quantity to utilize within 2 hours. Avoid fixing tiles outdoor when rain is imminent. Correct ratio of ADDCON Tile Adhesive and water is essential for optimum performance.

    Important Technical Data

    • Aspect : Grey Powder
    • Bulk Density : Around 1.35 (kg/ lit).
    • Bad Thicknes s: 3-6 mm
    • Open time : 30 Minutes
    • Pot Life : 1.5 Hrs

  • ADDCON TILE ADHESIVE – ULTRA

    Grey/White, Interior & Exterior Wall & Floor Tile & Stone Adhesive.

    Description

    ADDCON TILE ADHESIVE-ULTRA is a ready to use tile adhesive based on grey cement and special chemicals providing non shrink, self curing, waterproof excellent adhesive for vitrified Tile and ceramic tiles. Suitable for both horizontal and vertical surfaces, interior and exterior applications.

    Advantage

    • Very high polymer modified      982a2128
    • Non slip & Water resistance
    • Excellent bond than conventional cement based mortar
    • Self curing
    • Good mechanical strength
    • Applicable both horizontal and vertical surfaces
    • Flexible Adhesive
    • Impact Resistance

    Instruction for use

    Surface should be sound and mechanically cleaned to remove all loosely adhering particals,oil, grease etc. Pre-wetting of substrate is essential with maximum saturation of water but surface dry (S.S.D.) condition. Tiles shall be cleaned of dust with brush/cloth but shall be dry while using. ADDCON Tile Adhesive should be poured in the ratio of SC : W = 1: 0.25 to 0.30 by wt.into potable water slowly while stirring continuously to get smooth paste. Allow 5 minutes interval and stir again. Apply the paste on prepared surface with 5mm approx.thickness. and comb the surface with notched trowel.Place tiles within 2 hours of mixing and press firmly with twisting movement.Uneven surface may require more than 5mm thickness. Use damp cloth to remove excess paste from tile surface. Tile joints may be filled by ADDCON Tile grout.

    Coverage

    4kg to 5 kg per sq.mtr./5 mm. Thickness for flat surface (indicative)

    Packing

    20/25/50 kg Bag

    Storage

    Keep in a dry place, avoid moisture ingress.

    Caution

    Add powder to water. Prepare only required quantity to utilize within 2 hours. Avoid fixing tiles outdoor when rain is imminent. Correct ratio of ADDCON Tile Adhesive and water is essential for optimum performance.

    Important Technical Data

    • Aspect : Grey Powder
    • Bulk Density : Around 1.35 (kg/ lit).
    • Bad Thickness s: 3-6 mm
    • Open time : 20-30 Minutes
    • Pot Life : 1.5 Hrs

  • ADDCON EPOXY TILE GROUT

    Description

    Addcon EpoxyTilogrout is ready to use coloured epoxy resin based putty recommended for use as joint filling material between different tiles like, glazed wall tiles, vitrified and fully vitrified tiles, etc.

    Advantage

    • Ready to use
    • Easy to apply
    • Exceptional bond with the tiles
    • Water tight
    • Available in different colours

    Joint width

    1 – 6 mm

    Instruction for use

    • Fix the tiles with Addcon Tile Adhesive of appropriate grade.
    • Maintain a specified gap between the tiles
    • Allow the tile adhesive to hard. Ensure that there is no contamination or foreign particles in the open gap.
    • Then mix the three components of Addcon EpoxyTilogrout together. For this take Component A in a plastic container, to this add Component B.
    • Mix thoroughly for 2 minutes with a trowel. Then add Component C slowly to the liquid mix and mix with the trowel.
    • After the total C has been added mix thoroughly into a soft uniform coloured putty.
    • After mixing, apply the material using a float or trowel in to the gaps and compact to avoid any void information. Total mixing time should be maximum 6 minutes for the 2 kg prepacked material. The mixed material should be consumed within 30minutes after mixing.
    • Always use on a small areaat a time so that excess grout can be cleaned from the tile surface as soon as possible by using a Colma Cleaner with a dry sponge / cloth. Before cleaning the tile surface, wait for minimum 15 minutes.
    • During cleaning, move the sponge crosswise to the joints and not along the joints. The material should be used within the workable time.
    • Addcon Epoxy Tilogrout should be used after 24 hours of tile fixing.
    • Cleaning of tile joints should be done before the Addcon Epoxy Tilogrout has set on the tile surface. If required paint thinner can be used to clean thoroughly.

    Technical Data

    • Type: Epoxy
    • Aspect: Component A & B = Liquid, Component C= Coloured Powder
    • Mixing ratio , by weight: Comp.A: Comp.B: Comp. C= 2:1:8 to 9
    • Mixed Density: Around 2 kg / lit
    • Workable time at 30oC: Around 30 minutes
    • Setting time at 30oC: Around 75 minutes
    • Shelf life: 6 months in original packing

    Pack Size

    4.8kg.(Component A = 800 gm, Component B=400 gm, Component C = 3.6kg)

    Handling precautions

    Addcon products are generally quite harmless, provided certain precations are normally taken for handling chemicals. Avoid contact with foodstuff and foodutensils. Avoid prolonged skin contact. In the event of contamination, wash throughly with water. If the eye or mouth is effected, wash with clean water immediately.

    Important Notes: The information given in this data sheet is based on many years experience and is correct to the best of our knowledge. However, since success of our product in application will depend on number of factors, we can only be responsible for quality of our product at the time of despatch

  • Addcon Tile Grout

    Gap filling material between tiles

    Description

    Addcon Tile Grout is ready to use coloured cementitious powder containing special ingredients to solve the problems of conventional material.
    Addcon Tile Grout is recommended for use as gap filling material between different tiles like, glazed wall tiles, vitrified and fully vitrified tiles, etc.

    Advantage

    982a2102

    • Ready to use, only water to be added
    • Easy to apply
    • Water tight
    • Available in White, Black, Red, Copper, Ivory, Blue colour

     

    Joint width

    1 – 6 mm

    Instruction for use

    Fix the tiles with Addcon Tile Adhesive of appropriate grade. Maintain a specified gap between the tiles. Allow the tile adhesive to hard ensure that there is no contamination or foreign particles in the open gap. Then mix Addcon Tile Grout with water in the ratio of
    1 part water : 3 to 4 parts Addcon Tile Grout. Mix thoroughly until a lump free smooth paste of uniform colour is obtained. For mechanical mixing, avoid air entrapment in the paste.After mixing, apply the material using a float or rubber squeeze in to the gaps and compact to avoid any void formation. Always use on a small area at a time so that excess grout can be cleaned from the tile surface as soon as possible by using a wet sponge. Before cleaning the tile surface, wait for minimum 15 minutes. During cleaning, move the sponge crosswise to the joints and not along the joints. The material should be used within the workable time.

    After the grout has set finally, wash the tile surface with a clean cloth to remove any remaining paste.
    For improved resistance to acids and marine corrosion, Mix tile grout with Addcon Grout Admix

    Technical Data

    • Type – Cementitious
    • Aspect – Coloured powder
    • Workable time at 30 0C – Around 30 minutes
    • Shelf life – 6 months in original packing
    • Packing – 1 kg

    Pack Size

    1 kg.